LCD ReplacementMaybe your roommate stepped on your MacBook. Or maybe you put your backpackand threw it into the overhead bin of an airplane and somebody squashed it. Regardless of how it happens, broken LCDs are such a bummer, and the repair will usually cost you a couple hundred dollars. Some people might even go out and buy a whole new computer! Hi I’m mj with iFixit, and today I’m going to show you how to replace the LCD on your MacBook yourself. It’ll save you a lot of money, and it’s actually pretty fun. It’s possible to replace theLCDon any MacBook, but today I’m specifically repairing an original plastic MacBook, and as I do I’ll give you some tips on the trickier parts. Before you order your replacement LCD, it’s important to know you’ve got the right part for the right MacBook make sure you’ve got the right part for the right MacBook so check the model number of your computer on our site first. What’s great about thisrepair lcd is that you hardly need any tools to do it– I’ve got a coin, a plastic spudger, a card that I don’t mind damaging, a Phillips 00 screwdriver from our 26 piece bit driver kit, our replacement LCD of course and a screw tray which isn’t totally necessary but it useful since there are a lot of screws and a lot of steps.readmore
hi, now iam going to explain how torepair T.v. A lot of customers once they dismantle their TV and remove the bulb; will have something looking similar to this. This is out of the Sony TV, this one right here is out of a Mitsubishi DLP TV. Most DLP bulbs are the bulb itself and then they are in the plastic housing that is removable. Usually the bulbs are attached to theTVin one screw. When you remove the bulb from the TV you wanna make sure when handling the bulb, especially the new bulbs, that you’re wearing gloves that will prevent the oils from your finger from coming into contact with the lens. This is to prevent any heat spots from being created while the bulb is being used those heat sports can cause the bulb prematurely burn or cause different issues with the optical assembly in your TV. Proper handling: is you always wanna avoid contacting the front of the lens. Most bulb housings don’t need to be replaced you just need to replace the bulb inside with an original Osram or Phillips option. You also want to make sure you have Camtronics . A lot of people have canned air. Canned air alone isn’t good enough. There are a lot of different brands out there. We stick with the 3M brand and that’s the best brand. It’s what our technicians use. It doesn’t leave residue, it doesn’t cause short circuiting. You wanna follow the instructions on the can.Visit our site
Hi,Today we’re going explain how torepair microwave.to show you how to change the turntable drive coupling on your over the range microwave. It’s a really easy job; no tools required. Let me show you how we do it. Now to change the drive coupling on thismicrowavewe’re first of all going to remove the turntable tray and the support ring; and check the support ring while you we have it apart here to make sure that the wheels are not cracked and they turn freely. Then just remove the old drive coupling and discard it. We’ll take our new drive coupling and we’ll line up that D-shaft with the motor underneath. Make sure it drops firmly into place. Clean the surface area where the support ring goes, set it back in place, and while we have the tray out check that for any signs of chipping or cracking; they’re made of tempered glass and are prone to breaking if they have a chip on them anywhere; and as well take caution when washing these, that you don’t put them in too hot of water or too cold of water. Let them climatize first. Reinstall the tray and make sure it turns freely, and our repair is complete. We told you it was an easy job.contact us
Today we’re going expain howrepair washinh machine. It’s a really easy job. All we are going to need is a Phillips screw driver and a 5/16th nut driver. Let me show you how we do it. Now before we begin this repair, the first thing we should do is disconnect the power to thewasher. Simple pull the plug from the receptacle. Now the first step in this repair will be to remove the front panel. There are two Phillips screws, about an inch in from either side just under that lip. So either with a stubby Phillips screw driver or pull the machine forward enough so that you can tilt it back and remove those two screws. Once we’ve removed the two screws, we’ll pull the front panel out at the bottom and tilt it down to disconnect the two spring clips at the top. Now we can set that aside.
Hai this isdail and searchiam going to explainFridge repair.Today we are going to show you how to change the water inlet valve kit in your refrigerator. Pretty easy job, you need a quarter inch nut driver and a sharp utility knife. Let me show you how it’s done.your first step is to gain access to the interior of the control housing next remove the thermostat control kno release the old thermostat from the housing along with the temperature sensing tube taking note of their position disconnect the wires you’re now ready to install the new temperature control thermostat first straighten out the sensing tube and if applicable transfer the insulator from the old sensing tube to the new one connect the wires insert the new thermostat into place and conform the sensing tube to fit the housing replace the thermostat knob reposition and secure the control housing.you’re now ready to plug the appliance back in to make sure it’s functioning properly.Readmore